色欲aⅴ亚洲情无码AV蜜桃_少妇养生馆SPA私密精油按摩_久久精品国产香蕉亚洲AV_国产 在线 | 日韩

大家都知道鈑金圖紙的注意事項嗎？來告訴你

1展開方式要合理,盡可能減少不必要的工序及加工的方便性.考慮實際加工工藝,合理安排加工工序,(孔與折邊距離,壓鉚加工工藝,焊接加工工藝等,以上情形要考慮加工順序的安排) 

2合理選擇間隙及包邊方式 

間隙及包邊方式的選擇一般原則為:長邊包短邊,間隙根據板厚不同取值不同,一般為0.2~1.0mm. 

3必須合理考慮公差, 

圖面公差標注有如下幾種: 

A±a(公差不考慮),A0+a (不噴涂件,氧化件不須考慮走公差,噴涂件必需考慮走公差),A0-a(必須走公差),A+a-a(走平均公差) 

4對于門板類及盒體必須考慮毛刺方向 

對于該類零件的展開,必須要考慮毛刺,達到折彎后毛刺向里,對于一些大門板類零件設計時如未考慮烤漆掉掛工藝孔,而該零件又無其他孔,在展開時考慮加開掉掛工藝孔. 

5抽牙,壓鉚,沖凸,撕裂等位置方向必須明確,畫出剖面圖, 

6.對于圖面上不同孔徑的孔為了加以區別應該在圖面上用字母分別標識,不同孔徑采用不同的字母, 

7必須選擇合理的刀具 

8考慮烤漆及噴粉膜厚. 

9尺寸標注規范化,齊全,清楚,壓鉚類標注需統一規范化. 

尺寸標注規范化:在任一圖面繪制好尺寸標注前都要對尺寸標注比例進行設置,設置公式為AXP=1(A>0,P>0.P為設置值既overall scale值為P),尺寸文本字高為3. 

10材質,板厚要與表達方式相結合 

11選擇合適的圖紙幅面. 

12.特殊角度折彎系數及內R角變化要試驗確定. 

13部分尺寸較多的地方可畫出放大圖以便清楚表達. 

14.易出錯的地方需重點提示,如不對稱零件可在展開圖上畫出折彎示意. 

15對于需保護的地方要加以表示. 

16拉絲件要標明拉絲方向. 

17.所有折彎示意圖按標準一視角放置(即按我們的新圖框)毛刺面向里,不要因為放不下而改變放置位置, 可適當調節比例和選擇圖框,使得整幅圖面的排版美觀,整潔.所有折彎示意圖不可相交.